NIKLAS test engineering
Test benches for motors, pumps, gearboxes and test stations
We build every test bench around your test item: we adapt the fixture, measuring equipment, guarding and software to the design, dimensions and test scope.
Selected customers
Test benches for recurring test tasks
We clarify which test bench suits your task in a conversation about the test item, test scope and quantity.
NIKLAS Motor BenchElectric motor test bench
You test electric motors and fans electrically and mechanically, with a guided test sequence, test report and Health Monitor.
Learn more
NIKLAS Test FieldTest station to DIN EN 50191
High-voltage, insulation and protective conductor testing at the test station, also as an EOL test station at the end of production. We build it in the guide sizes S, M and L or to custom dimensions.
Learn more
NIKLAS Pump BenchPump test bench to ISO 9906
You measure the characteristic curve, power and efficiency of your pumps, also in the version for fire-fighting centrifugal pumps.
Learn more
NIKLAS Drive BenchGearbox test bench
You test industrial gearboxes after repair or production for run-in, load stages, endurance run and efficiency.
Learn more
NIKLAS Vision CheckVisual inspection system
You inspect parts by camera and inspection recipe, also as a module in the modular test bench system.
Learn more
NIKLAS Safety OneSafety tester, new for 2027
Safety One tests high voltage, insulation and protective conductor in one device and shows the affected measuring path in the event of a fault.
Learn moreOne test software for all test benches
Each of our test benches comes with guided test sequences, limit values for each test item and a digital test report.
Sample view of the test software. The range of functions and parameters depend on the agreed configuration.
What all test benches have in common
The same test software runs on every test bench. It guides the test sequence and creates a digital test report.
The software stores limit values for each test item.
You transfer the test data to your ERP system via a data interface.
Frequently asked questions about our test benches
Here we answer questions about the types of test bench, the shared test software and how an enquiry is handled.
Which test benches do you build?
We build the Motor Bench electric motor test bench, the Test Field test station to DIN EN 50191, the Pump Bench pump test bench to ISO 9906, the Drive Bench gearbox test bench and the Vision Check visual inspection system.
We design and build the test benches in Barbing near Regensburg.
We clarify which test bench suits your task in a conversation about the test item, test scope and quantity.
What should an enquiry for a test bench include?
Test items with variants, test tasks, measured variables with tolerances, cycle time, installation site and the acceptance you require. You will find a checklist with all points in the Knowledge article Requirements specification for a test bench.
What do all test benches have in common?
The same test software runs on every test bench. It guides the test sequence, stores limit values for each test item and creates a digital test report.
You transfer the test data to your ERP system via a data interface.
The range of functions and parameters depend on the agreed configuration.
How is a test bench designed for my test task?
We build every test bench around your test item: we adapt the fixture, measuring equipment, guarding and software to the design, dimensions and test scope.
For the Test Field, sizes S, M and L serve as guide values. We also build to custom dimensions.
Describe the test item, test scope and quantity. We get back to you with a proposal for the set-up and sequence.
Who are the test benches intended for?
For maintenance departments, repair shops and workshops that want to test and document motors, pumps, gearboxes or assemblies after production, modification or repair.
The Vision Check is aimed at production and inspects parts directly in the process.
Enquire about a test bench for your test task
Describe the test item, test scope and quantity. We get back to you with a proposal for the set-up and sequence.
Simon Niklas
Mechanical engineer, M.Sc.
+49 941 56956720[email protected]
“Good engineering proves itself in day-to-day production. That is why we combine technical planning with a close understanding of process, operation and maintenance.”
Book a consultation